After you have received the new seats for your RV, there are a few things you need to know before starting the installation process. This step-by-step guide will walk you through everything else that needs to be done after you have unboxed and clicked the pieces together.
Before we begin, here are some helpful links that you may find useful for this installation:
Please note that some of these links may be affiliate links. This means that if you make a purchase using our link, we may earn a small commission at no additional cost to you. We greatly appreciate your support. In this informative video by RVLivingLIFE, the focus is on the step-by-step guide to installing Thomas Payne Theater seats in an RV. The video starts after the seats have been assembled, and it covers various aspects of the installation process. From moving the seat belts to replacing the receptacle, shortening the valance arms, attaching the seats to the floor, and removing the plastic from the front, the video provides a comprehensive guide for viewers. The speaker expresses disappointment with the quality control of the seats but mentions that the assembly process itself is simple. The video also discusses the challenges faced during the delivery of the seats and the remaining tasks involved in properly mounting the seats to the floor and making necessary adjustments and modifications. Ultimately, the speaker describes the final result as looking good and being thoroughly enjoyed.
Throughout the video, the friendly and engaging tone of the speaker shines through as they share personal experiences, explain the installation process, and express their satisfaction with the end result. Viewers are guided through each step, allowing them to follow along and learn how to install Thomas Payne Theater seats in their own RV.
Step 1: Removing the Old Sofa
Before you can start the installation of your new Thomas Payne Theater seats, you’ll need to remove the old sofa from your RV. This involves several steps, including disconnecting the seat belts, removing the sofa from the RV, and clearing the space for the theater seats.
To begin, you’ll need to disconnect the seat belts that were attached to the old sofa. This will ensure that they don’t interfere with the installation of the new seats. Be sure to follow any specific instructions provided by the manufacturer for disconnecting the seat belts.
Once the seat belts are disconnected, you can proceed to remove the old sofa from your RV. This may involve unscrewing or unbolting any fasteners that are holding the sofa in place. Carefully lift and remove the sofa from the RV, making sure to have assistance if needed due to the weight and size of the sofa.
After removing the old sofa, you’ll need to clear the space for the theater seats. This may involve cleaning the area and removing any debris or furniture that may be in the way. Take measurements to ensure that the new seats will fit properly in the available space.
Step 2: Replacing the Receptacle
Now that you have cleared the space for the theater seats, you can move on to replacing the receptacle. This is necessary to accommodate the new seating and the refrigerator plug. Follow these steps to replace the receptacle:
-
Start by removing the plug for the old sofa. This may involve unscrewing or disconnecting any fasteners that are holding it in place. Carefully remove the plug, making sure to avoid damaging any wiring.
-
Install a double receptacle in its place. This will provide enough outlets to plug in the theater seats and the refrigerator. Follow the manufacturer’s instructions for installation, making sure to securely attach the receptacle to the wall.
-
Once the double receptacle is installed, you can plug in the theater seats and the refrigerator. Make sure to check that all connections are secure and that the seats and refrigerator are functioning properly.
By replacing the receptacle, you ensure that all necessary electrical connections are in place for your new seating arrangement. This will make it easier to enjoy your theater seats and use your refrigerator without any issues.
Step 3: Shortening the Valance Arms
To prevent interference with the new theater seats, you may need to shorten the valance arms. The valance arms are the arms that hold the valance, which is the decorative fabric panel that covers the top of the window. Here’s how you can shorten the valance arms:
-
Start by measuring and marking the valance arms to determine how much needs to be trimmed. Measure from the bottom of the valance arms to the desired height, taking into account the clearance needed for the theater seats.
-
Use a saw or other appropriate cutting tool to carefully cut the valance arms to the marked length. Make sure to follow proper safety precautions when using any cutting tool.
-
After cutting the valance arms, ensure that they are securely attached to the wall or window frame. You may need to use screws or other fasteners to reattach the valance arms to the desired height.
By shortening the valance arms, you eliminate any potential interference with the theater seats and ensure that they fit properly against the wall. This will give your RV a clean and streamlined look.
Step 4: Connecting the Theater Seats
Now that you have made the necessary adjustments to accommodate the theater seats, it’s time to connect and assemble the different parts of the seats. Follow these steps to properly connect the seats:
-
Start by assembling the different parts of the seats according to the manufacturer’s instructions. This may involve attaching the seatbacks, armrests, and other components.
-
Once all the parts are assembled, carefully connect the seats to each other. Make sure that the connection is secure and that the seats are aligned properly.
-
Plug in the seats to ensure proper functionality. Check that all electrical connections are secure and that any built-in features, such as heating or massage functions, are working properly.
By properly connecting the theater seats, you ensure that they are securely in place and functioning as intended. Take the time to double-check all connections and functionality to ensure a comfortable and enjoyable seating experience.
Step 5: Moving the Seat Belts
With the theater seats in place, you’ll need to move the seat belts to accommodate the new seating arrangement. This is necessary to ensure safety and compliance with regulations. Follow these steps to move the seat belts:
-
Determine the new placement of the seat belts based on the new seating arrangement. This will vary depending on your specific RV and the type of theater seats you have installed.
-
Remove the seat belts from their original location and reposition them to the new desired location. This may involve unscrewing or unbuckling the seat belts and attaching them to a new mounting point.
-
Make sure that the seat belts are securely attached and that they are properly aligned to provide maximum safety. Double-check all connections to ensure that they are tight and that the seat belts are functioning as intended.
Moving the seat belts is an important step to ensure that you and your passengers are safely secured while traveling in your RV. Take the time to properly adjust and secure the seat belts according to the new seating arrangement.
Step 6: Adjusting the Seats to Fit Close to the Wall
To maximize the use of the available space in your RV, you may need to adjust the seats to fit close to the wall. This will create more space in the center of the RV and allow for easier movement. Follow these steps to adjust the seats:
-
Start by making any necessary adjustments to the theater seats. This may involve adjusting the seatbacks, armrests, or other components to a more compact position.
-
Ensure that the seats are properly aligned and centered against the wall. This may involve shifting the seats slightly or adjusting their position.
-
Double-check all adjustments to ensure that the seats are securely in place and that they fit snugly against the wall. This will create a clean and streamlined look in your RV.
By adjusting the seats to fit close to the wall, you maximize the use of the available space and create a more comfortable and spacious seating area. Take the time to properly align and secure the seats for the best results.
Step 7: Covering the Hole in the Desktop
During the installation process, a hole may have been made in the desktop. To create a more aesthetically pleasing look and hide the hole, you’ll need to cover it with an appropriate material. Follow these steps to cover the hole:
-
Start by identifying the size and shape of the hole that needs to be covered. This will help you determine the appropriate covering material.
-
Choose a covering material that matches the existing desktop or complements the overall design of your RV. Common options include wood veneer, laminate, or fabric.
-
Securely attach the cover to hide the hole. This may involve using adhesive, screws, or other fasteners, depending on the type of covering material.
By covering the hole in the desktop, you create a cohesive and visually appealing look in your RV. Take the time to choose the right covering material and securely attach it for the best results.
Step 8: Mounting the Seats to the Floor
To ensure stability and prevent movement while traveling, you’ll need to mount the theater seats to the floor of your RV. Follow these steps to properly mount the seats:
-
Start by securing the seats in the desired position on the floor. Make sure that they are aligned properly and centered in the available space.
-
Use the appropriate tools and techniques to securely attach the seats to the floor. This may involve drilling holes and using screws or bolts to fasten the seats.
-
Double-check all connections to ensure that the seats are firmly attached and that they do not move or shift while traveling.
By mounting the seats to the floor, you create a safe and stable seating area in your RV. Take the time to properly secure the seats to prevent any potential accidents or injuries while on the road.
Step 9: Shortening the Awning Arms
To prevent interference with the theater seats, you may need to shorten the awning arms. The awning arms are the arms that support the awning and allow it to extend and retract. Follow these steps to shorten the awning arms:
-
Start by measuring and marking the awning arms to determine how much needs to be trimmed. Measure from the bottom of the awning arms to the desired height, taking into account the clearance needed for the theater seats.
-
Use a saw or other appropriate cutting tool to carefully trim the awning arms to the marked length. Make sure to follow proper safety precautions when using any cutting tool.
-
After trimming the awning arms, adjust and secure them according to the manufacturer’s instructions. This may involve using screws or other fasteners to ensure that the awning arms are securely attached.
By shortening the awning arms, you eliminate any potential interference with the theater seats and ensure that they can be fully extended and retracted without any issues. This will allow you to enjoy the benefits of your RV’s awning while still having comfortable seating.
Conclusion
In conclusion, the installation of Thomas Payne Theater seats in your RV can greatly enhance your comfort and enjoyment while on the road. By following the step-by-step guide provided in this article, you can easily navigate the various aspects of the installation process, including removing the old sofa, replacing the receptacle, shortening the valance arms, connecting the theater seats, moving the seat belts, adjusting the seats to fit close to the wall, covering the hole in the desktop, mounting the seats to the floor, and shortening the awning arms.
Throughout the installation process, be sure to pay attention to safety precautions and follow the manufacturer’s instructions for each step. Take the time to properly adjust and secure all components to ensure a safe and comfortable seating area in your RV.
Once the installation is complete, you can enjoy the overall satisfaction of a job well done. The Thomas Payne Theater seats will provide you with a comfortable and stylish seating option in your RV, allowing you to relax and unwind during your travels.